CART (0)

Your shopping cart is empty

View Cart
Close

Please select your country or region to be
directed to the appropriate Lesker site.

Aluminum Oxide Crucibles for E-Beam Sources

Overview

  • Custom sizes available upon request.

  • Insulating crucibles are not typically recommended for e-beam evaporation. As the electrons bombard the material in the crucible liner, these electrons need a path to ground otherwise they will accumulate on the material and charge the material. When enough charge accumulates, it will start to deflect the e-beam. Electrically insulating crucible liners are not a good idea to use in an e-gun because of this. We recommend that all metals be done in electrically conductive crucible liners for this reason. The electrons can then be conducted through the material, through the crucible liner, then into the hearth in this way.

Common Causes of Crucible Breakage

  1. The ramp/soak levels are wrong for that material. A recipe for e-beam consists usually of two ramp/soak power levels. This allows for the gradual heating of the material to a point where deposition can start. When deposition starts there is a transfer of power control from the ramp/soaks to a PID loop control between the e-gun power supply and the quartz crystal controller. If ramp2/soak2 power level is not near the power level to hit the specified deposition rate (say 1 Angstrom/sec) this means the PID loop must try very hard or search very hard to try and get rate. Since the PID loop is in control of the power, power can oscillate dramatically (+90% to 0%) for a while before the PID loop finally gets the power at the right level to control at that 1 Angstrom/sec rate. Wild swings in power rapidly liquefy and then condense the material several times even before the deposition starts. This will crack any crucible. It is best to get the ramp2/soak 2 power level very close to the power needed to hit the desired rate. This way when the PID loop takes over control, it does not need to adjust power that much to hit rate - just a slight tweak. This prevents this rapid liquefy/condense process from occurring. So incorrect Ramp levels can definitely cause crucible cracking.

  2. The second reason is much easier - the user shuts the power supply off or has a very short ramp down time for power after the deposition is done. This causes the rapid solidification of the melt, and this stresses out the crucible liner.


► Show Fill Rate Calculator

Material Deposition Chart
The Material Deposition Chart is useful to determine the optimum vacuum deposition technique, thermal source, and power supply requirements.
Evaporation Sources FAQ
Click here for answers to some of the most common questions we are asked.
Contact Us
Contact Us
Questions? Let's Talk!
Contact your dedicated Lesker sales team today.
+1 800 245 1656


Aluminum Oxide E Beam Crucibles


Aluminum Oxide E-Beam Crucibles

More
Info
Reference Pocket Volume Liner Volume (cc) Description Part Number Price Ready to Ship Add To Cart
More
Info
Reference Pocket Volume Liner Volume (cc) Description Part Number Price Ready to Ship Add To Cart
Aluminum Oxide 4 Use 2.1 cc as the liner volume value in the calculator above 2.1 ALUMINUM OXIDE CRUCIBLE LINER, 0.885" TOP OD X 0.595" HIGH X 0.093" WALL THICK, 15 DEGREE WALL ANGLE, 4CC POCKET VOL, 2.1CC LINER VOL, PER DRAWING EVCEB-22ALO $215.00 4-5 Weeks

Aluminum Oxide E-Beam Crucibles

More
Info
Reference Pocket Volume Liner Volume (cc) Description Part Number Price Ready to Ship Add To Cart
More
Info
Reference Pocket Volume Liner Volume (cc) Description Part Number Price Ready to Ship Add To Cart
Aluminum Oxide 7 Use 4.4 cc as the liner volume value in the calculator above 4.4 ALUMINUM OXIDE CRUCIBLE LINER, 1.167" TOP OD X 0.563" HIGH X 0.093" WALL, 15 DEGREE WALL ANGLE, 7CC POCKET VOL, 4.4CC LINER VOL, +/-0.005" ALL, PER DRAWING EVCEB-4ALO $119.00 In Stock

Aluminum Oxide E-Beam Crucibles

More
Info
Reference Pocket Volume Liner Volume (cc) Description Part Number Price Ready to Ship Add To Cart
More
Info
Reference Pocket Volume Liner Volume (cc) Description Part Number Price Ready to Ship Add To Cart
Aluminum Oxide 15 Use 8.2 cc as the liner volume value in the calculator above 8.2 ALUMINUM OXIDE CRUCIBLE LINER 1.48" TOP OD X 0.67" HIGH, 15 DEGREE WALL, 0.125" WALL, 1/PKG, 15CC POCKET VOL, 8.2CC LINER VOL, PER DRAWING EVCEB-13ALO $197.00 In Stock

Aluminum Oxide E-Beam Crucibles

More
Info
Reference Pocket Volume Liner Volume (cc) Description Part Number Price Ready to Ship Add To Cart
More
Info
Reference Pocket Volume Liner Volume (cc) Description Part Number Price Ready to Ship Add To Cart
Aluminum Oxide 25 (4 Pocket) Use 17.1 cc as the liner volume value in the calculator above 17.1 ALUMINUM OXIDE CRUCIBLE LINER, 1.85" TOP OD X 0.68" HIGH, 0.093" WALL, 15 DEGREE WALL ANGLE, 4 POCKET, 25CC POCKET VOL, 17.1CC LINER VOL, PER DRAWING EVCEB-16ALO $194.00 4-5 Weeks

Aluminum Oxide E-Beam Crucibles

More
Info
Reference Pocket Volume Liner Volume (cc) Description Part Number Price Ready to Ship Add To Cart
More
Info
Reference Pocket Volume Liner Volume (cc) Description Part Number Price Ready to Ship Add To Cart
Aluminum Oxide 25 (6 Pocket) Use 16.3 cc as the liner volume value in the calculator above 16.3 ALUMINUM OXIDE CRUCIBLE LINER, 1.633" TOP OD X 0.940" HIGH X 0.093" WALL, 15 DEGREE WALL ANGLE, 6 POCKET, 25CC POCKET VOL, 16.3CC LINER VOL, PER DRAWING EVCEB-25ALO $194.00 4-5 Weeks

Aluminum Oxide E-Beam Crucibles

More
Info
Reference Pocket Volume Liner Volume (cc) Description Part Number Price Ready to Ship Add To Cart
More
Info
Reference Pocket Volume Liner Volume (cc) Description Part Number Price Ready to Ship Add To Cart
Aluminum Oxide 30 (With Web) Use 21.9 cc as the liner volume value in the calculator above 21.9 ALUMINUM OXIDE CRUCIBLE LINER, 1.92" TOP OD X 0.81" HIGH, 15 DEGREE WALL, 0.093" WALL, W/ WEB 30CC POCKET VOL, 21.9CC LINER VOL EVCEB-26ALO P.O.R. KJLC will contact you

Aluminum Oxide E-Beam Crucibles

More
Info
Reference Pocket Volume Liner Volume (cc) Description Part Number Price Ready to Ship Add To Cart
More
Info
Reference Pocket Volume Liner Volume (cc) Description Part Number Price Ready to Ship Add To Cart
Aluminum Oxide 40 Use 30.4 cc as the liner volume value in the calculator above 30.4 ALUMINUM OXIDE CRUCIBLE LINER, 2.03" TOP OD X 1.02" HIGH, 0.125" WALL, 15 DEGREE WALL ANGLE, 1/PKG EVCEB-6ALO $310.00 In Stock

Aluminum Oxide E-Beam Crucibles

More
Info
Reference Pocket Volume Liner Volume (cc) Description Part Number Price Ready to Ship Add To Cart
More
Info
Reference Pocket Volume Liner Volume (cc) Description Part Number Price Ready to Ship Add To Cart
Aluminum Oxide 6 Use 2.4 cc as the liner volume value in the calculator above 2.4 ALUMINUM OXIDE CRUCIBLE LINER, 0.936" TOP OD X 0.593" HIGH X 0.093" WALL, 15 DEGREE WALL ANGLE, 2.4CC LINER VOL, PER DRAWING EVCEB-5ALO P.O.R. KJLC will contact you

Aluminum Oxide E-Beam Crucibles

More
Info
Reference Pocket Volume Liner Volume (cc) Description Part Number Price Ready to Ship Add To Cart
More
Info
Reference Pocket Volume Liner Volume (cc) Description Part Number Price Ready to Ship Add To Cart
Aluminum Oxide 12 Use 8.11 cc as the liner volume value in the calculator above 8.11 ALUMINUM OXIDE CRUCIBLE LINER, 1.334" TOP OD X 0.768" HIGH X 15 DEGREE WALL ANGLE, 0.093" WALL THICKNESS, 12CC, PER DRAWING EVCEB-33ALO $156.00 7-8 Weeks

Aluminum Oxide E-Beam Crucibles

More
Info
Reference Pocket Volume Liner Volume (cc) Description Part Number Price Ready to Ship Add To Cart
More
Info
Reference Pocket Volume Liner Volume (cc) Description Part Number Price Ready to Ship Add To Cart
Aluminum Oxide 12 Use 6.26 cc as the liner volume value in the calculator above 6.26 ALUMINUM OXIDE CRUCIBLE LINER 1.350" TOP OD X 0.680" HIGH X 0.125" WALL, 15 DEGREE WALL ANGLE, 12CC POCKET VOL, 6.26CC LINER VOL. EVCEB-31ALO P.O.R. KJLC will contact you

Aluminum Oxide E-Beam Crucibles

More
Info
Reference Pocket Volume Liner Volume (cc) Description Part Number Price Ready to Ship Add To Cart
More
Info
Reference Pocket Volume Liner Volume (cc) Description Part Number Price Ready to Ship Add To Cart
Aluminum Oxide 20 Use 14.6 cc as the liner volume value in the calculator above 14.6 ALUMINUM OXIDE CRUCIBLE LINER, 1.673" TOP OD X 0.768" HIGH X 0.093" THICK WALL, 15 DEGREE WALL ANGLE, 20CC POCKET VOL, 14.6CC LINER VOL, +0/-0.005" ALL, , MIN ORDER OF 5, PER DRAWING EVCEB-29ALO P.O.R. In Stock

Aluminum Oxide E-Beam Crucibles

More
Info
Reference Pocket Volume Liner Volume (cc) Description Part Number Price Ready to Ship Add To Cart
More
Info
Reference Pocket Volume Liner Volume (cc) Description Part Number Price Ready to Ship Add To Cart
Aluminum Oxide 7 Use 3.7 cc as the liner volume value in the calculator above 3.7 ALUMINUM OXIDE CRUCIBLE LINER, 1.125" TOP OD X 0.520" HIGH X 0.093" WALL, 15 DEGREE WALL ANGLE, 7CC POCKET VOL, 3.7CC LINER VOL, ALL PER DRAWING EVCEB-23ALO $119.00 4-5 Weeks

Aluminum Oxide E-Beam Crucibles

More
Info
Reference Pocket Volume Liner Volume (cc) Description Part Number Price Ready to Ship Add To Cart
More
Info
Reference Pocket Volume Liner Volume (cc) Description Part Number Price Ready to Ship Add To Cart
Aluminum Oxide 3 Use 1.4 cc as the liner volume value in the calculator above 1.4 ALUMINUM OXIDE CRUCIBLE LINER, 0.805" TOP OD X 0.545" HIGH X 0.093" WALL, 15 DEGREE WALL ANGLE, 3CC POCKET VOL, 1.44CC LINER VOL, 1/ PKG EVCEB-21ALO P.O.R. KJLC will contact you

Aluminum Oxide E-Beam Crucibles

More
Info
Reference Pocket Volume Liner Volume (cc) Description Part Number Price Ready to Ship Add To Cart
More
Info
Reference Pocket Volume Liner Volume (cc) Description Part Number Price Ready to Ship Add To Cart
Aluminum Oxide 2 Use 0.84 cc as the liner volume value in the calculator above 0.84 ALUMINUM OXIDE CRUCIBLE LINER, 0.706" TOP OD X 0.465" HIGH X 0.093" WALL, 15 DEG WALL ANGLE, 2CC POCKET VOL, 0.84CC LINER VOL, PER DRAWING EVCEB-20ALO P.O.R. KJLC will contact you
Contact Us - Aluminum Oxide Crucibles for E-Beam Sources

▲
To Top