Overview
The Cool Drawer Single Sensors allow crystal installation into the sensor from the side, convenient for systems with insufficient room for front load crystal installation. The Cool Drawer Single Sensor employs the Cool Drawer Crystal Holder which is thermally shielded by the water-cooled housing insuring excellent crystal performance.
One or more of these sensors should be purchased with each controller. Each sensor comes completely assembled and includes integral water tubes, In-vacuum coaxial cable (Front Load) or In-vacuum conduit (Cool Drawer), water tube bending tool, crystal snatcher(Front Load), and operating instructions. All air and water tubes (except the bakeable sensor) are 1/8 inch (0.32cm) O.D. All shuttered sensors require the 750-420-G1 pneumatic control valve. Limited use with other controllers is possible - call KJLC at +1 800 245 1656 or click here to contact us with any technical questions.
Features
- No internal cables
- Cool Drawer crystal holder
- Easy installation
- Bakeable if ordered with welded CF40 flange
- Available with: CF40 feedthrough and 2.54 cm (1") bolt feedthrough
- Adjustable length if ordered with compression fittings
- No brazing required if ordered with compression fittings
- Sensor/feedthrough combination available welded to customer specified lengths
Specifications
| Cool Drawer Single Sensor | ||
|---|---|---|
| Finish | Stainless steel, gold plated Cool Drawer™ | |
| Cooling water | 0.2 GPM using 1/8" O.D. tube (Do not allow to freeze) | |
| Crystal | Industry standard 0.550" diameter | |
| Air supply | Shuttered sensors require 55-60 psi regulated | |
| Electrical connection | One standard female BNC on atmosphere side | |
| 1" Bolt and Compression Fitting Terminations | ||
| Materials | 304 stainless steel, Teflon®, ceramic, beryllium nickel, VITON® | |
| Temperature | Operational environment to 300° C with water cooling or 165° C without< | |
| Mounting | 1.015" ±0.010" diameter aperture | |
| CF 40 Welded Terminations | ||
| Materials | 304 stainless steel, Teflon, ceramic, beryllium nickel | |
| Temperature | Operational environment to 450° C with water cooling or 200° C without | |
| Mounting | Mates with 2.75" ConFlat type flanges with 1.375" I.D. min. | |
Configuration Options
Ordering Code Example: CDS-A0F37-66
| Type of Sensor (includes user manual, crystals sold separately) |
Code | Configuration |
| Standard cool drawer (water lines parallel to crystal face) |
A | A |
| Right angle cool drawer (water lines perpendicular to crystal face) |
B | |
| Shutter Assembly | Code | Configuration |
| None | 0 | 0 |
| Standard shutter | 1 | |
| Length of Sensor (see notes 1 and 3) |
Code | Configuration |
| Length: 10-66cm (4-26") | F | F |
| Feedthrough (see notes 2 and 4) |
Code | Configuration |
| 1" bolt | 3 | 3 |
| CF40 | 4 | |
| Feedthrough Connection (see notes 2, 3, and 4) |
Code | Configuration |
| Sensor welded to feedthrough | 7 | 7 |
| Feedthrough equipped with Ultra-Torr compression fittings (allows for adjustable sensor length). NOT AVAILABLE WITH CF40 FEEDTHROUGH AND SHUTTER COMBINATION. | 8 | |
| Welded Sensor Length (see notes 1 and 2) (Use only when feedthrough connection is 7 Not required when feedthrough connection option is 8) |
Code | Configuration |
|
Weld length in centimeters, 10-66 cm (4-26") Other lengths may be available: contact factory. Other lengths will be considered a special order and will be subject to additional cost and lead time. |
10-66 | 66 |






